Skip to content
sigmalistOpen app

Methods & practice / Practical guide

Final Version: a practical guide to choosing your next task

By Sigmalist · A practical assessment

What is Final Version?

Final Version (FV) is Mark Forster’s method for choosing work from a running list. This guide covers the original FV, rather than the later Final Version Perfected (FVP). Forster’s explanation, published by Beeminder, is linked below.

Start with the source: Mark Forster: Forster Lists, or Final Version (Beeminder).

How to use Final Version

  1. Keep a running list

    Write down work you want to do. Append new tasks as they occur to you.

  2. Select the first task

    Dot the first unactioned item. Leave it selected while you look further down the list.

  3. Build a chain

    Scan forward. Select a task when you want to do it before your latest selection. Use that new selection as the next comparison, continuing to the end.

  4. Work backward

    Take action on your selections in reverse order. Some progress is enough; you need not finish each task.

  5. Carry unfinished work forward

    Cross out actioned entries, re-enter unfinished work at the bottom, and start another chain from the first unactioned item.

Where it can help

  1. 01You can spend less time ranking everything

    Assigning a priority to every task can become a project of its own. A selection routine gives you a smaller decision to make at each point. That can be useful when several jobs matter and none has an obvious claim on the next hour.

  2. 02A session can include an uncomfortable task

    If an awkward conversation keeps getting postponed, it may help to have a session that includes both preparing for it and making the call. Notice whether your chosen routine actually gets you there. Finishing a few pleasant jobs is useful only if it leaves room for the commitment too.

  3. 03You can measure progress without demanding completion

    A first draft or a short investigation can move a project forward even when it remains open. Recording what changed and what remains gives the next session a clearer starting point.

Where it gets difficult

  1. 01Selection can become another way to delay

    You can spend a long time comparing tasks or revising the list. If a session ends before any work begins, simplify the task descriptions and notice how much time the choosing takes.

  2. 02Deadlines still need attention

    Check your calendar and commitments before starting. A submission due in an hour needs a deliberate decision about time. Do not assume your preferred sequence will leave enough room for it.

  3. 03Repeated small starts can leave projects unfinished

    Opening a document is useful once. Repeatedly opening it without adding anything is a signal to change the approach. Define a useful stopping point, such as drafting the first paragraph, and check whether the work is advancing.

Using it in Sigmalist

  1. 01Keep automatic first selection enabled

    In Sigmalist Settings, leave ‘Automatically add the first task to the stack’ on. It is enabled by default. The preference applies to new picking sessions; a session already in progress keeps its starting mode.

  2. 02Choose, then work through the stack

    Select Start working on your list, then Compare next task. Use Pick it when you want to work on the highlighted task before the latest selection, or Not now to move on. Focus begins with your last pick. Sigmalist adapts the paper method into a stack and lets started work become a continuation.

  3. 03Continue unfinished work without copying it

    When you stop partway through a task, add a continuation instead of rewriting it by hand. The new entry goes to the end of the list, and the earlier one stays visible but crossed out. That trail shows how often you returned to the work. It is a record of effort, not a sign that you failed.

What it looks like in practice

Suppose your list contains ‘Draft the workshop outline’, ‘Book the meeting room’, ‘Send the attendance question’, and ‘Archive old notes’, in that order. Select the outline first. You would rather book the room before drafting, so select that too. You would rather send the attendance question before booking, so select it. Leave the old notes alone. Your working order is now: send the question, book the room, then draft. After writing three outline points, record what still needs developing for a later session.

Who is it a good fit for?

Try it if you already capture tasks but struggle to turn the list into action. It may be less useful when your day is mostly appointments or work assigned in a fixed sequence. You can reserve the experiment for the part of the day you control.

Try one work session

Choose a short list of real tasks and allow time for one session. Check any deadlines first. Follow the steps, then note what changed in the work itself. Did you begin the task you usually avoid? Was selecting quick enough to be useful? Try another session only after looking at those results.

Common questions

Is Final Version the same as Final Version Perfected?

No. FVP is a later revision with different selection instructions. Use one version consistently while learning; this guide teaches FV.

How is it different from Resistance Zero?

FV begins with an automatic first selection and compares later tasks with the latest selection. Resistance Zero considers each task independently for whether it feels free of resistance, including the first task.

What if I keep avoiding the same commitment?

Look at the obstacle directly. You may need information, a smaller deliverable, help from someone else, or a conversation about the commitment. Changing the order of a list cannot resolve every reason a task is difficult.

Sigmalist is independent and is not affiliated with or endorsed by the creators of the methods discussed here. The tradeoffs here are editorial judgments, not promises of particular results.